Crafts ’n things Craft of the Day
Fusing glass is so easy when you use Diamond Tech’s line of Fuseworks tools! Create these vintage-looking earrings to celebrate the last days of summer!
- Diamond Tech: Fuseworks Bug-A-Boos Fuse Art Decals, Opalescent White 90 COE Fusing Glass
- Delphi Glass Gold Plated Round Cabochon Mini Links (85435), two
- White oven-bake polymer clay, small amount
- Gold findings, two each: headpins, earring wires
- Diamond Tech Fuseworks Glass Cutter, Kiln Paper, Kiln; Studio Pro Running Pliers
- Pliers: chain-nose, round-nose
- Wire cutters
- Acrylic paints: gold, black
- Microwave oven
- Parchment-lined baking sheet and oven
- Eclectic Products E6000 Industrial Strength Adhesive
ruler, soft cloth, oven mitts, craft knife, damp paper towel, scissors, container of water, paintbrush, newspaper (to cover work surface)
1. To cut white glass, position on flat cutting surface with smooth side facing up. Starting on edge of glass and holding cutter firmly in one hand, push cutter gently and evenly across glass. Decrease pressure slightly as you reach the opposite edge of the glass; lift cutter off glass at end. Hold glass in one hand, with score facing up. With other hand, center score line in jaws of running pliers about 1/2” onto glass surface. Apply pressure to handles until glass separates into two pieces. Cut four 3/8”x3/8” squares from white glass. Clean and dry with soft cloth.
2. Cut 2”x2” from kiln paper to fit base of kiln. Place paper on kiln base. Arrange two 3/8” glass squares on top of kiln paper about 1/2” apart. Place another square on top of base square at 90º angle so corners of top square hang over sides of base square. Carefully place kiln base with glass on center of microwave oven. Place lid on top of base.
3. To achieve full fuse, microwave on high for 2-1/2 minutes. (Note: Every microwave oven and kiln will vary. If using a microwave with a lower wattage, keep the time consistent but increase the power.) When microwave time has expired, use oven mitts to carefully open lid. If glass is not fused to your liking, return kiln lid to base and place in microwave for 30 second intervals until fused. (Note: Glass is VERY hot. Be extremely careful and never touch the glass.)
4. When desired results have been achieved, use oven mitts to remove kiln from microwave oven. Set kiln on heat resistant work surface and let cool for 30-45 minutes. (Note: Do not leave the lid off the kiln for an extended period of time during this stage. Removing the lid may cause your glass to crack.)
5. While glass is cooling, create two mini beehives by rolling 1/2” balls of clay into cone shapes. Use craft knife to carve three horizontal lines around each cone. Insert headpin through bottom center of each cone. Follow manufacturer’s instructions to bake beehives on parchment-lined baking sheet in oven. Let cool.
6. Once fused glass from kiln has cooled, remove fiber paper from back of glass by rubbing surface with damp paper towel.
7. Use scissors to cut out two bumblebee decals. Cut tiny slits around edges of each decal to help set on rounded surface. Place decals in container of water for 30 seconds. Slide backing paper off decal and set on cooled glass. (Note: The decal should slide off backing paper easily. If it doesn’t, let soak in container of water for 10-15 more seconds.) Use paper towel to pat moisture from decal and glass. Smooth out air bubbles with fingertip. Let dry thoroughly before firing.
8. Cut 2”x2” from kiln paper and place on base of kiln. Place two pieces of glass on top of kiln paper. Carefully place kiln in microwave oven. Follow fusing guide on decal packaging for best results when fusing decals. Use oven mitts to carefully open kiln lid after time has expired. If white residue appears on decal, return kiln lid to base and place in microwave for 30 second intervals until white residue disappears. (Note: Never touch the glass. Glass is VERY hot.) Let glass completely cool for 30-45 minutes before removing from kiln.
9. On covered work surface, paint each beehive gold. Let dry. Lightly paint with (1:1) mixture of black paint and water. Let dry for about 10 minutes. Drybrush beehives gold. Let dry.
10. Adhere each fused glass piece to front of cabochon link using glue. Let set.
11. Use chain-nose pliers to bend wire end on headpin in beehive to 90º angle. Grasp headpin with round-nose pliers and pull wire up and over top of round-nose pliers to form full loop. Cut excess wire off looped end on headpin using wire cutters. Open loop and attach onto bottom link on cabochon; close loop to secure. Attach earring wire to top link on cabochon. Repeat process for other earring.
by Lauren DiSanza for Diamond Tech (www.diamondtechcrafts.com)