Fall Leaves Table Runner

Crafts ’n things Craft of the Day

Tired of looking for just the right table runner to match your décor? Design your own using basic sewing instructions and stamping techniques. The possibilities are practically endless!

Materials

  • Fabrics, 2 yards each: unbleached muslin; cotton or poly-cotton, light green or color of choice
  • Sage cording, 4 yds.
  • Sage tassels, 3” long

Tools

  • Sewing machine and matching thread
  • Stamps: ivy leaves, birch leaves
  • DecoArt Acrylic Paints: Terra Cotta, Antique Gold, Hauser Light Green, Dazzling Metallic Emperor’s Gold
  • Fabric pencil, or dressmaker’s chalk

Basic Supplies

scissors, yardstick, T-square, straight pins, iron, paintbrush, paper plate, paper towels, container with soap and water

Directions

Size

12”x60”

Table Runner

1. To sew top of table runner, use yardstick, T-square, and fabric pencil, to measure and mark a 13”x61” rectangle on muslin fabric; cut out. See Figure 1. To shape each end into a point, trim away corners as shown.

Figure 1

2. Using top as pattern, cut one backing from green fabric and one lining from muslin.

3. Place backing, right side up, on work surface. See Figure 2. Pin cording to edges of backing so cording faces inward, and cording overlaps at one edge. Pin one tassel, tassels facing inward, to each end. Using zipper foot, sew cording and tassels to backing.

Figure 2

4. Pin muslin layers to right side of backing. Use zipper foot to sew back and front together, leaving an 8” opening at one side for turning.

5. Turn table runner right side out. Whipstitch opening closed; press.

6. Use paintbrush to apply paint to leaf stamps. See Stamping Tips below. Apply paint in a thin, even layer. Practice stamping on fabric scrap until you are confident about the amount of paint and pressure to use. Stamp all leaves using the same paint color at one time. Wash stamp with mild soap and water and dry thoroughly before changing colors. Repeat stamping/cleaning/drying process until all paints have been used.

Tip

  • Instead of making a table runner from scratch, give an old one new life by embellishing with stamped designs, new tassels, or other trims.

Stamping Tips

  • If the stamps include more than one size leaf, apply paint to one leaf at a time, stamp design, then wash and dry stamp before changing leaf size or color.
  • Here’s an easy way to arrange your design. Paint three or four leaves, both birch and ivy, using each color of paint, onto paper. Cut out paper leaves and arrange on table runner. When satisfied with arrangement, pin leaves in place to use as a painting guide.
  • In case of a misplaced paint drop or slip of the stamp, change design slightly and add a leaf to cover the mistake.

by Connie Matricardi

Burlap and Butterflies Pillow and Table Runner

Crafts ’n things Craft of the Day

 

Something other than a sack made from burlap? You bet! Stamp butterflies onto burlap to create this pillow and table runner, plus learn the trick to cutting straight, even edges on burlap fabric!

Materials

  • Natural burlap fabric, 36” or 45”-wide, 2 yds.
  • White cotton fringe, 4” long, 3-1/4 yds.
  • Pillow form, 16” square

Tools

  • Stamps: butterfly, fern
  • Plaid Apple Barrel Colors White Acrylic Paint
  • Fabric-painting medium
  • Glaze sponge
  • Sewing machine and matching thread
  • Beacon Adhesives Fabri-Tac Permanent Adhesive

Basic Supplies

scissors, iron and pressing surface, ruler

Directions

Sizes

Pillow, 16” square; Runner, 21”x35”

Pillow/Table Runner

1. Apply adhesive to cut edges of burlap; let dry. Wash burlap in hot water without fabric softener. Press to remove wrinkles.

2. For straight-edge cutting guide, pull two threads across width of burlap; cut along line. Measure 18” from straight edge and pull two threads across width again for 18”-wide fabric piece.

3. For pillow, cut two 18” squares from burlap. Cut 21”x35” rectangle for runner, using same thread-pulling method for straight edges.

4. Follow manufacturer’s instructions to mix paint with fabric-painting medium. Use sponge to apply paint to stamp. Stamp runner and one pillow square. See Tip.

5. To assemble the pillow, pin fringe around edges of stamped pillow square, with fringe ends toward center. (Note: Gather fringe slightly in corners to prevent puckering.) Pin remaining square to pillow.

6. Sew pillow together with 5/8” seams, leaving 12” of one side open for turning. Trim corners close to stitching and turn right side out. Insert pillow form; slipstitch opening closed.

7. Zigzag or overcast stitch around runner edges. Press 1” to wrong side along 35” edges; straight stitch in place. Pin fringe along 19” edges, wrapping ends around to back side; topstitch in place.

Tip

  • Practice stamping on scrap burlap. Mark center with pin. Press stamp firmly, then lift straight up; do not rock from side to side.

by Barbara Matthiessen